Monday, January 21, 2013

DIY Roman Shade

You guys... this post has been a LONG TIME in the making!!  The last time I brought this project up was back in October (original post here).  

After months and months, I finally get to share with you this DIY for making your own Roman Shade!  This project took me somewhere in the ballpark of 8-10 hours in total, however, it's important to remember that I've never sewn anything in my life before, so the learning curve for me was pretty steep!! While this project took mere hours, it's taken me over 4 months to complete, photograph, and post!  Without further delay, let's get to it.  


Here she is... my DIY roman shade... and she's hanging like a champ in our hallway!

I really tried my best to document every single stage of the project, but it got way more difficult in the last few steps since Kris and I were both standing on chairs, trying to hang this sucker... 

Step one: find fabric.  I ended up ordering a bit over two yards of Secret Gate from Lewis and Sheron Fabrics (online)... remember this post  from way back in September??  That's how long this has been in motion...

Ok anyway, the FABULOUS fabric arrived, and after dawdling a bit, I decided to tackle this project.  That was step two. Easy peasy.

Step three: iron the fabric - trying to tackle measurements on wrinkled fabric is a big no-no (or so my mama told me)... and so I ironed away!


And then I ironed some more....


And some more... until it was perfectly smooth (side note, that's not my beautiful kitchen in the below photograph... ours is perhaps the ugliest room you've ever seen.  These beautiful cabinets are at my parents house - jealous?)


Once the fabric is ironed, it's time to do some math.  This was by far my least favorite part of this project, and the part I was definitely the worst at.  Thank god for my mom!  She corrected it several times, but let me see if I can recap how you need to measure.

Write down the length and width of the window.  Once you have that, decide if you want your shade to be the exact length and width, or how much wider than the window you want your shade to be.  If you want the shade to be wider than the window, add on the amount you want it to be wider to each side (for example, if the window is 40" wide, and you want an additional inch on each side, add two inches, for a total shade width of 42 inches).

If you are lining this, it gets a bit more complicated.  You'll want your printed fabric to wrap around to the back side of the shade, and the lining to be less wide, so add on additional width for the fabric to wrap around to width you've already estimated (if you want the printed fabric to wrap around 2" on each side, add an additional 4".  Make sense??

Finally, keep about 5 extra inches of "front side" fabric for wrapping around the piece of wood for mounting - no lining fabric needed here.  You can cut off extra fabric later if you don't end up needing it, but you can't really add more on if you are short!


Ok, once the measurements are made, and your fabric is cut, start pinning the lining to the fabric.  As you are pinning, you want the print side of the fabric to be face up, and the lining to be on top.  This way once you sew the seams, and you turn it "inside out" so the seams face in, and the print faces out.


When you have finished pinning, the fabric will look odd - each side sort or folded over - that's because the lining is more narrow than the front facing fabric for the extra length to wrap around (so you don't see the seams or lining from the side once the shade is finished).

This picture below is how it should look.


Ok onto sewing.  Set up the sewing machine (I could not help explain this step, but if you sew, just follow the instructions with the bobbin, etc), and sew along the seams, taking the pins out as you go.


Halfway through, I realized my outfit matched the fabric - it was a good omen!!


After both seams are sewn, flip it inside out... or "right side out" I guess, and iron it again, so the fabric edge is even on both sides.

It should look like the below picture from the back side, with the lining not going all the way to the edge.

Next step is to get out the measuring tape again, and start marking off where the rings will go.  Ignore the wrinkles in this photo, it started out ironed, but got wrinkled after sitting folded on the table for three months.

I wanted fewer, larger folds, so I pinned every 17" or so for a 70" window, I got 4 pleats.




A note I left out above was that at the bottom of the shade, I inserted a wooden dowel cut down to the width of the window, and sewed it in.  This rod inside the bottom of the shade acts as a weight so that when the shade is pulled up, it hangs properly.  You can kind of see the rod in the above picture.  Some people put these dowels up the entire length where each fold will be, but I didn't find it was necessary.  My shade pulls up just fine - perhaps my fabric is heavy enough (and I ironed the folds in, so it has the memory).

Anyways, getting back to the point... sew three vertical rows of these rings onto the shade.  One on each side, and one in the middle.


Be sure these rings are really secured on there - they are what is supporting the shade when it's pulled up and down - I used a drop of super glue to make sure the rings and thread were super secure.  I'm not sure this is necessary, but I feel better about it.


So this is the part where photo documentation became shoddy, so I apologize.

The final steps here are super simple.

Prepare your mount - I used a piece of wood 1"x2" and started by stapling the shade onto the wood, wrapping it around, to cover all sides.  Once the fabric was stapled, I screwed in single hook screws into the wood (through the fabric).  These look like a more sturdy eye hook.  With that prepped, it's time to thread the shade.

This below picture, pretty much illustrates everything more clearly than I can put into words.
Tie the cord to the bottom rings, and make sure the knot is really tight (I also used superglue here so the knots won't come undone).  The cord furthest from where you will pull the shade up should be longest, the one in the middle the second longest, and the cord on the side with the pulley should be shortest.  Thread each cord up through the loops on the shade, and then through the eye hooks screwed into the mount on the top.

Final stage mounting - I used L shaped brackets, and some super long screws to get this up.  Once it was secured above the window we were ready to test out the shade, and praise the lord, it WORKS!  

That moment, seeing the shade go up and down was really cool, to see that after all that measuring, sewing, and installing, that it actually worked.  I was half waiting for it to collapse, pull up crooked, or whatever, but it was super simple, and dare I say it, foolproof!


And here it is from the side.. pretty awesome...


And the pleats from the front - this was completely accidental, but the pattern is perfectly lined up - cause I'm a ballerrrrrrr!!


Here is a close up of the pulley system in action, along with the mounts... 


And a final glory shot of the curtain, hanging in the hallway - it's so pretty, although in these pictures, I am completely realizing that I forgot to wrap the side of the wood mount.  I painted it white, but I'm not loving that unfinished edge.  I'll have to go back in with a little hot glue gun, and swatch of fabric to finish off the ends!


If you are thinking of attempting a roman shade of your own and have some questions, just shoot me an email!  I could NOT have done this without my mama's help!

xoxo

67 comments:

  1. Amazing how great it turned out. I don't have a single diy bone in my body so I'm not sure I can pull this one off!

    ReplyDelete
    Replies
    1. I think you can! It takes more patience (and math skills) than anything else!!

      Delete
    2. where did you find the rings?

      Delete
    3. Everything I needed was from Joanne's Fabrics! They sell roman shade kits with the cord, rings and brackets, or you can get it all separate (which is what I ended up doing)!

      It was way too convenient, but you could also order them online here:
      http://www.draperysewingsupplies.com/Shade-Rings-s/19.htm

      Good Luck!!

      Delete
    4. I may be tired and just not getting it, but I can't tell how your cord system stays in place after pulling it up. Are you just wrapping it around a bracket on the wall once the cords are pulled up, or is there a locking system you bought that's attached? By the way thank you for your blog. I have a 15 in window, and you can't buy blinds for them without it being ridiculously expensive. Even the cheep slat kind everyone is using to make the roman blinds. Thanks for another option :)
      Leslie McKnight

      Delete
    5. It's not just you! Take a look at the second to last photo - this is really the only one that shows how the pully's work.

      I used eye hooks, and screwed them into the wood, aligned with the rows of rings that went up the back of the curtain. The cords thread through the rings, and finally up through the eye hooks - be sure the cords are long enough to thread across, and drop down so they hang down even when the curtain is lowered fully. The purple circles in my illustration (with the multi colored threads) are where the eye hooks are anchored.

      Once everything is threaded, and the wood / curtain is mounted on the wall, the shade stays up with a cleat screwed into the wall - there is no mechanism to "hold the shade up" other than tying it to the cleat, which works just fine for us!

      Hope this helps!

      Delete
    6. So do you actually sew the tape of rings to the two layers of fabric?

      Delete
    7. Yes, you need to sew the rings through both the face fabric and the lining.

      Delete
  2. No matter much you tug, it’s tough to get the motorized shades fort worth into the exact position you want. By motorizing them, they can move in one fluid movement to the right spot. If you have a bank of windows, every shade can move in perfect alignment. As for draperies, you no longer need to use those unsightly rope pull cords.

    ReplyDelete
  3. What a wonderful creation, Becky! You don't have to have the blinds to make it aligned. You only need the hooks! Anyway, I think the secret is keen attention for the right measurement and proper symmetry.

    #Roxie@WindowTreatmentsPhiladelphia.com

    ReplyDelete
  4. Your roman shade is definitely hanging pretty, Becky! Reading about how much you worked to get this project done, I feel somewhat proud that you finally finished it! Haha! Anyway, blinds and shades, with their main purpose of controlling the amount of light that comes into our house, can also accentuate our windows. So thinking about the make of the window before deciding on the style and design of the curtain to put up should be greatly considered too. Good luck on your future projects!
    Rene @ Beltway Blinds

    ReplyDelete
    Replies
    1. Aww, thank you! Many man hours went into this, but it's still hanging like a champ in our hallway!

      Delete
  5. Hey Becky, thanks for putting this tutorial together. I really like the way your roman shades turned out. One quick question - when you attached the rings to the back - did you only sew this through the lining or did you tack it through both layers into the main fabric too?

    ReplyDelete
    Replies
    1. Hey there! When I attached the rings, I actually sewed them all the way through both the lining and the main fabric, and you can't see the stitches at at all. I think part of this is because I used a patterned fabric, and part of it is because it's a looser woven linen, so they really blend in. If you're using a plain fabric, or a fabric with a tight flat weave, you may be able to see it when the shade is down, but most of the time the shades are pulled up!

      Good luck! Would love to hear how it turns out!

      Delete
    2. Awesome, thank you so much. I am hoping to get these knocked out in the next couple of weeks and will let you know. Thanks!!

      Delete
    3. Awesome!! Let me know if you have any more questions as you get started working on yours :-)

      Delete
  6. We have amazing style of blinds,curtains,bed sheets,pillows,sofa setting and have great designs of interior designs so we have offered many colours for bed sheets and have sexy and hot blinds and curtains themes.

    ReplyDelete
  7. Hi Becky, I'm writing from a book publishing company in the UK, we would like to contact you regarding collaborating on a project - would you kindly contact me at freelance@rotovision.com and i'll send you a full email.

    Thanks,
    Alison
    www.rotovision.com

    ReplyDelete
  8. This comment has been removed by a blog administrator.

    ReplyDelete
  9. That looks really lovely. Thank you so much for providing such simple instructions with corresponding detailed graphics on how to sew it. I also think that the fabric is really simple, yet very stylish, which really brings out the beauty of the sunlight on a window. 
    Greg Arnett

    ReplyDelete
  10. This comment has been removed by a blog administrator.

    ReplyDelete
  11. After analysis of your posting, I can not leave your excellent posting without appreciating it; in fact, your Posting is a great treasure for the visitors.

    ReplyDelete
  12. Your great posting always leaves long lasting impressions on me. Your website is also very attractive, as you know a business without having a professional website is not considered a professional business.

    ReplyDelete
  13. Its great blog, full of knowledge and pleasure; a very experience.
    Thankful to you by Hosting Company UK.

    ReplyDelete
  14. It’s an impressive blog; I would like to invite others to visit your postings time and again.
    Yours Best-wishers: Asghar- Enterprises.

    ReplyDelete
  15. There is no doubt about the excellence of your posting, the whole piece of work is an inspiring effort especially for us, as we are a website company, so we regularly observe your latest updates and enjoy it.

    ReplyDelete
  16. That particular blog post is written artistically and it includes many practical knowledge for everybody. I guess you've carried out a great job of handling this delicate.




    Roller Blinds & Vertical Blinds

    ReplyDelete
  17. Your Blog is an admirable one as I am a General Practitioner and Doctor, so I go through the postings minutely, and yours one I found a fantastic piece of work.

    ReplyDelete
  18. Every time when I visit your posting its always fantastic like the present one which increases the horizons of my mind. Now a day Boxes and Gift Boxes, in other words Corrugated packaging has become a necessity for each and every Product to present it decently.
    Thanking You
    Pick A Box

    ReplyDelete
  19. Your posting is a master piece of creativity in the real sense. I prefer it to all others which I have visited until now. According to my point of view, not only among the posh families Curtains & Blinds are considered a symbol of status but in the business world and latest outlets also blinds and curtains are taken as a great factor.

    ReplyDelete
  20. After viewing your posting I would like to appreciate your honest efforts which deliver a clear vision to the readers and visitors. We are Panel Beaters in Johannesburg. We always like to share our views with others.

    ReplyDelete
  21. These look great!! I especially like the look of the rings and not the slats. Just an FYI, I went back and looked at my custom roman shades that I special ordered, and the ends are not covered, so I don't think anyone would notice that you didn't cover yours other than you :-) great job!!

    ReplyDelete
  22. Excellent tutorial. I have been dreading making Roman Shades with all the terrible posts out there with dowels, staying mechanisms, etc. You made it look like it is doable. I will be trying this in the next couple weeks. Thank you.

    ReplyDelete
  23. So glad I found your tutorial. I have written instructions from a decorator, but some steps are missing. Your directions are the first ones I found for a lined shade using the rings. My question is do you sew the rings to the lining only or to both the lining and fabric? Did you sew them on by hand or with your machine? I read somewhere that you could use the zigzag stitch to attach the rings, which would mean the thread would show in the right side of the fabric.

    ReplyDelete
    Replies
    1. Did you get an answer, Cheryl? She did answer the same question earlier, if you scroll back past all the spam you'll find it.

      Delete
  24. I Love this. For a long time now I wanted to know how to make this and set up the pulley system. You explained it very simply and did a fantastic job. Thank you sooo much for sharing!

    ReplyDelete
  25. The shades look great but I am afraid to try such crafts. Instead I have to spend lots of money to have these things made for me. I am so jealous!

    ReplyDelete
  26. Hello. I bought amazing fabric and now I am finally ready to tackle this project. So happy I found it. Now, I have some questions. The room where my blinds will be is pretty dark so I Bought light fabric and feel I should not line it as to not make the room darker. So basically they are more for privacy than shade. If I don't use the lining fabric, I am guessing I still should sew the seems, right. Also, would it be a problem with the little hooks? I'm guessing they will show on the front side and maybe rip the fabric when pulled? Would a thin lining work instead? Thanks!

    ReplyDelete
  27. The stunningly beautiful prints, colours and the fabric material of one such sheer roller blinds that I bought online from a designer home furnishing store in London was of premium quality and that made the difference to the overall aesthetics and ergonomics of my kitchen area which now represents a much more refined, soothing and refreshing look through this beautiful custom Roman blind.

    ReplyDelete
  28. can you please indicate what I am needed for this project.Including yhe size of the wood that you put on top of it, l really want to make my own.

    ReplyDelete
  29. This sounds like the best tutorial I have seen so far. I am making my own roman shades. Thank you so much for posting

    ReplyDelete
  30. What an amazing work really worth to read!! Love it!! there is knowledge to gain from. blinds singapore is really vital in our home. Btw, you can check and visit also our website https://www.cottoncare.com.sg offering services in affordable prices. Thank you and Keep it up!! :)

    ReplyDelete
  31. For rooms or media rooms, select the room obscuring texture shading choice, where 4 1/8" Room Darkening shading vanes and 2 5/8" sheer texture vanes substitute to guarantee most extreme security roller window shades are incredible at sifting light and simple to keep up at a lower cost from DBS Blinds. Free examples and transportation to make requesting simpler!

    ReplyDelete
  32. To utilize the empty plot areas to its best then make the finest information of sketch map directly into a 2D floor plans, forward the design to the client knowledge, and that too from 3D Rendering, India.

    ReplyDelete
  33. This comment has been removed by the author.

    ReplyDelete
  34. There are lots of styles for hanging fabric curtains to inspire people rem cua bang vai

    ReplyDelete
  35. Thanks For the message.

    If you need edge technology & trend-setting designs of Top-Down Window Shades to make your residence beautiful and outstanding in Toronto and Muskoka towns, then Concord Shading Systems Inc. is here to help you.

    For More Info:- concordshading .com

    ReplyDelete
  36. Congratulation for the great post. Those who come to read your Information will find lots of helpful and informative tips. Diy Roller Blind

    ReplyDelete
  37. Thank you for sharing it, Just loved the way you presented it.
    3D interior designer in ontario

    ReplyDelete
  38. If you are tired of your old roller blinds but do not have enough money to buy ones, you could simply decorate your roller blinds and make them look stylish and brand new. When remodelling a home

    Roller Blind

    ReplyDelete
  39. If you are tired of your old roller blinds but do not have enough money to buy ones, you could simply decorate your roller blinds and make them look stylish and brand new. When remodelling a home

    Roller Blind

    ReplyDelete
  40. If you are tired of your old roller blinds but do not have enough money to buy ones, you could simply decorate your roller blinds and make them look stylish and brand new. When remodelling a home

    Roller Blind

    ReplyDelete
  41. This is such a great resource that you are providing and you give it away for free. I love seeing blog that understand the value of providing a quality resource for free. DIY roller blinds

    ReplyDelete
  42. This is very educational content and written well for a change. It's nice to see that some people still understand how to write a quality post.! DIY roller blinds

    ReplyDelete
  43. Its great blog, full of knowledge and pleasure; a very experience.

    Custom made blinds

    ReplyDelete
  44. Team Designs is the best 3D rendering service provider in Australia. We offer the latest 3d designs according to customer expectations and requirements. We provide a large variety of 3d rendering, 3d interior designs, 3d product rendering, 3d animation, 3d industrial rendering and 3d floor plans for homes, residential apartments, office and industrial designs, etc.

    ReplyDelete
  45. Our Learn to Swim kids program gives uninterrupted learning for your children all year round. Baby Swimming Lessons are accompanied 49 weeks of the year to support for consistent training and to present students with the possibility to grow through levels at a quicker rate. The Star Swim Schools provides you peace of mind that your kid will receive a high-quality swimming education.
    Women's Swimming Lessons

    ReplyDelete
  46. Are you looking to purchase Modern blinds Naples? If yes, Hitech-Shades is here to help. We provide a wide range of window treatments at very reasonable prices.

    ReplyDelete
  47. The pretty impressive tone of writing. The wordings were simple which made me understand the topic more easily.
    Get the most reliable Shade Structures Supplier Qatar for your outdoor purposes. Also available in different styles.

    ReplyDelete
  48. Thanks For sharing this great post!! it's so pretty, although, in these pictures, I like it so much. The experience I was lucky to have with QLD Blinds and Security must be shared. I had high expectations and approved all of them. They provide quality roller blinds in Gold Coast at reasonable prices.

    ReplyDelete
  49. Thanks for sharing this DIY Roman Shade tutorial! Your hard work paid off – it looks fantastic in your hallway. 😍

    ReplyDelete
  50. Absolutely loved this DIY Roman shade tutorial! Thanks for the step-by-step guide - I can't wait to try making my own stylish window treatment.

    ReplyDelete
  51. Great tutorial on making your own Roman shades! The step-by-step instructions were easy to follow, and I appreciate the clear pictures that accompany each step. Now I feel confident enough to try making one for my living room. Thanks for the helpful guide!

    ReplyDelete